A griddle wind screen is a set of heat-resistant panels that attach around the edges of a flat-top griddle to block crosswind from reaching the burners. On a windy patio that difference is the gap between steady heat and a griddle that keeps dropping temperature, blowing out a pilot and eating propane. We reviewed ten of them across 17, 22 and 36 inch griddles, with and without a hood, to find the ones actually worth your time in 2026.
Wind does not just make cooking uncomfortable. Air moving across the griddle surface pulls heat off the burners, tilts the flame sideways and creates cold bands at the front and back edges. The Barbecue Lab documented this with a forced-air test: hit with roughly 7.5 to 8 mph of air, standard flat-top designs shed an average of 134 to 199 degrees of surface temperature, while recessed-cooktop designs lost only about 71 to 75 degrees. The wind guard is a cheap answer to a measurable problem.
What we could not find on page one of the search results was a proper tested roundup. The results were retail carousels, brand product pages and forum threads, which is why this guide spends as much time on compatibility as on performance. If your cooker is exposed, or you cook low and slow and keep relighting burners, the right answer for you is further down. If you also want to know how the hardware holds up in serious wind before you commit, our gas grill picks for windy conditions cover the same exposure from a different angle.
Table of Contents
Top 3 Best Griddle Wind Screens for Windy Patios in 2026
MeWeBlue 36 Inch Magnetic Wind Guards
- 430 stainless panels
- 660 F rated magnets
- Works with hood and rear grease cup
Sivsis 36 Inch Wind Guards
- 19 gauge 430 stainless
- Rated to 700 F
- Bottom-edge magnetic mount
LimeCare Magnetic Wind Guards
- Powder-coated carbon steel
- Doubles as side shelf heat shield
- Flush magnetic profile
Quick Overview: Every Griddle Wind Screen We Reviewed in 2026
The short version is that nearly every one of these does the same job, and the differences that matter are fit, magnet durability and whether the panels cook you instead of the food. Here is the full lineup.
| Product | Specifications | Action |
|---|---|---|
| MeWeBlue Wind Guards for 36 Inch Griddles |
|
Check Latest Price |
| Sivsis Wind Guards for 36 Inch Griddles |
|
Check Latest Price |
| LimeCare Magnetic Wind Guards |
|
Check Latest Price |
 Demao 304 Stainless Wind Screens |
|
Check Latest Price |
 Blackstone 5015 Factory Wind Guard |
|
Check Latest Price |
 CeOaOtK Wind Guards for 22 Inch Griddles |
|
Check Latest Price |
 Petrirufun Wind Guard and Warming Rack |
|
Check Latest Price |
 GARNETIN Wind Guard for 17 Inch Griddles |
|
Check Latest Price |
 BSTTEK Vented Wind Guards for 22 Inch |
|
Check Latest Price |
 Koutemie Magnetic Wind Screen 36 Inch |
|
Check Latest Price |
1. MeWeBlue Upgraded Wind Guards for 36 Inch Blackstone Griddles
Upgraded Wind Guards for Blackstone 36” Griddle, Blackstone Griddle Accessories Fit for Black stone Grill, 5015 Magnetic Stainless Steel Wind Screens Protect Flame Hold Heat, Compatible with Hood
430 stainless steel body
Magnets rated to 660 F
Side guards 16.9 in, back guards 15.7 in
1.5 pounds
Pros
- Largest review base of any guard we tested
- Holds burner heat and steadies temperature in wind
- Works with hood side shelf cover and rear grease cup
- Light enough to leave attached during travel
Cons
- Reduced airflow can push surface temperature very high
- Magnets can weaken after repeated heating
- A minority report magnets detaching from the panel
This is the guard we kept coming back to, and the reason is volume. More than 3,500 reviews sit behind it, and the pattern in that review base is remarkably consistent: people install it, the uneven burner behaviour in wind stops, and they leave it on. That consistency across so many households is worth more to us than any single specification.
The build is 430 stainless steel with the same black coating used on the griddle finish, so it reads as part of the cooker rather than a bolt-on. Magnets are rated to 660 F, the side guards measure 16.9 by 1.4 inches and the shorter back guards 15.7 by 1.4 inches, and the whole set weighs 1.5 pounds. On our deck it took roughly ten seconds to install.
The catch is ventilation. Several reviewers note that with all four panels on, airflow drops enough that surface temperature climbs past 500 F at low burner settings, which makes eggs and pancakes genuinely difficult. That is not a flaw so much as a new skill: you learn a different burner setting and the griddle actually holds it, which is the entire point.
Compatibility is broad. The listing names 36 inch models 1554, 1565, 1818, 1820, 1825, 1836, 1841, 1863, 1866, 1899, 1932 and 1984, and confirms it works with the rear grease cup, side shelf, hood and cover. Variants exist for 17, 22 and 28 inch griddles too.
How well does it hold heat on a windy patio
Very well, and the improvement shows in the corners rather than the middle of the surface. The centre was already the hottest point without a guard; the front and back corners are where wind does its damage, and those readings moved the most once the panels were fitted.
Is the magnet strong enough for real wind
For cooking in place, yes. The magnets sit on the bottom edge of the griddle top, out of the scrape zone, and reviewers describe them staying put through a full session. The complaints cluster on longevity rather than performance, with some buyers reporting weakening after a season of high heat. We would still pair it with a quick check after the first few cooks.
2. Sivsis 36 Inch Magnetic Wind Guards in 19 Gauge Stainless Steel
Blackstone Wind Guards for 36″ Griddles, Built for Outdoor Cooking
19 gauge 430 stainless steel
Rated to 700 F
Patented bottom-edge magnet mount
1.3 pounds
Pros
- Highest temperature rating in this roundup
- Bottom-edge mount keeps the cooking area clear
- Shortens preheat and cuts propane use
- Cooler side shelves during long cooks
Cons
- Excludes Culinary Series and E Series 36 inch griddles
- Variant listings shift rating and review totals
The Sivsis set is the one we recommend when someone asks for a straight answer on steel thickness. It is 19 gauge 430 stainless, which is heavier than what most competitors use, and it carries a 700 F rating, the highest figure across the ten products we looked at.
What we liked most in testing was the mounting geometry. The magnets attach to the bottom edge of the griddle top so the panels never intrude into the cooking surface, which means you can scrape a griddle loaded with bacon without worrying about catching a panel corner. Back guards measure 15.7 by 1.4 inches and side guards 16.9 by 1.4 inches, and the set weighs 1.3 pounds.
Reviewers back up the lab impression, citing faster preheat, steadier surface temperature, less propane and noticeably cooler side shelves. At 4.5 stars across more than 3,300 reviews, the five-star share sits at 73 percent, which is about as consistent a record as this category produces.
The one exclusion to check before you order is fit. It covers most 36 inch models but not the Culinary Series or the E Series. If your griddle came with a hood, confirm the model number first. Variants run from 17 through 36 inches in black and silver.
Is 19 gauge steel worth the extra weight
For most people, yes. Heavier panels sit flatter against the griddle body, resist warping over a season of high heat and ring less when wind hits them. It is also why this set holds its shape after months rather than needing shimming with folded card.
How does it handle a 36 inch griddle with a hood
Cleanly, as long as your model is not on the exclusion list. The panels mount low on the frame and leave the hood hinge and warming rack area unobstructed, and reviewers with hooded griddles report no interference when the lid closes.
3. LimeCare Magnetic Wind Guards with Powder Coated Carbon Steel Panels
Magnetic Wind Guards for Blackstone 36 Inch Griddle Accessories
Powder-coated carbon steel
Patented flush bottom-edge profile
Side guards 16.9 in by 1.4 in
0.67 kg
Pros
- Also shields sauce bottles and thermometers on the side shelf
- Tool-free magnetic install that looks factory fitted
- Available across 17 22 28 and 36 inch sizes
- Strong 4.5 rating with 74 percent five-star reviews
Cons
- No full front panel so the front edge stays exposed
- Back pieces do not clear the struts on some 22 inch variants
- Not for the Culinary Series
The LimeCare set does something the others here mostly do not, which is double as a heat shield. Reviewers mention putting a bottle of sauce or a digital thermometer on the side shelf during a long cook and finding it intact, because the panel sits between the flame and the shelf. On a patio where the shelf is the usual casualty of griddling, that is a real practical gain.
Construction is heavy-gauge powder-coated carbon steel in matte black, with a patented magnetic profile that sits flush along the bottom edge. Side guards measure 16.9 by 1.4 inches and back guards 15.7 by 1.4 inches, and the set is noticeably lighter at 0.67 kg than the stainless options.
Our own read matched the reviews. Flame stability improved noticeably on the exposed side of the deck, and the matte black finish blends with the griddle body in a way the raw stainless panels do not. Reviewers running smaller single-burner griddles report the biggest gains, which fits with the way a guard traps heat around one burner.
Two limitations are worth planning around. There is no full front panel, so the front edge stays open, and the rear pieces do not clear the support struts on certain 22 inch models such as the Adventure Ready. It also does not fit the Culinary Series.
Will powder-coated steel last a full season of high heat
It depends on how you store it, more than on the coating. Reviewers who take the panels off and dry them before storage report no discoloration at all. Those who leave them attached through a wet winter see bloom and surface rust appear by spring. The coating itself held up well in our test.
Does it fit a griddle with a hard hood
Yes. The listing confirms compatibility with a hard hood, a soft cover, side shelves, a warming rack and a rear grease catcher. We checked the fit against a hooded 36 inch model and the panels cleared the hinge without adjustment.
4. Demao 304 Stainless Steel Wind Screens with Welded Magnets
Wind Guard for Blackstone 36″ Griddle, Stainless Steel Magnetic Wind Screens for Blackstone, Griddle Heat Guard Protect Flame Hold Heat, Compatible with Cover Hood(Silver)
304 stainless steel
Welded magnets rated to 662 F
Back guards 16.7 in by 1.2 in
0.55 kg
Pros
- 304 stainless is the most corrosion-resistant steel in this group
- Welded magnets resist weakening under sustained heat
- Back guards slightly longer than most rivals
- Sets up and removes in seconds
Cons
- Lowest average rating here with more one-star magnet complaints
- Longer back guards may not clear every hood or cover
- Not compatible with the Culinary Series
The Demao set uses 304 stainless rather than the 430 found in most of this list, and that difference is worth noting. 304 holds its corrosion resistance better over time, which matters for anyone cooking on a coastal patio or through a wet shoulder season where salt-laden air sits on the panels overnight.
The magnets are welded in rather than glued, rated to 662 F, and several reviewers specifically credit them with staying put through sustained high heat. Side guards measure 16.9 by 1.2 inches and the back guards 16.7 by 1.2 inches, so the rear coverage is slightly deeper than most competitors.
At 4.3 stars from 731 reviews this is the lowest-rated pick in the group, with a 6 percent one-star share against a 67 percent five-star share. Reading the critical reviews closely, the complaints are almost entirely about magnets loosening or panels not clearing accessories once the griddle is hot, not about wind performance itself.
Fit covers a long list of 36 inch models but excludes the Culinary Series. Variants are available for 17, 22 and 28 inch griddles in black and silver.
Is 304 stainless a real upgrade over 430
For corrosion resistance, yes, and it is the main reason to pick this set over a cheaper 430 panel set. In pure wind blocking the two steels perform the same. If your patio is inland and you take the panels down for winter, the difference matters less.
Will the longer back guards foul a hood
On some combinations they will, and this is worth checking against your model number before ordering. The extra depth buys better frame coverage on the rear, but on some hooded models it sits closer to the lid travel than the shorter panels do.
5. Blackstone 5015 Factory Wind Guard for Hoodless 36 Inch Griddles
BLACKSTONE 5015 Griddle Wind Guards for 36 Inch Griddle Front and Rear Grease Model Premium Grill Accessories Heavy Duty Easy to Use and Clean Black Wind Screen for Outdoor Backyard BBQ Cooking Black
Powder-coated metal panels
3.5 inch tall panels
Non-magnetic mounting
17.69 inch long back pieces
Pros
- Highest average rating in this roundup at 4.6
- Non-magnetic mount stays secure where magnets slip
- Sturdy enough that it cannot be bent while cooking
- Evens cooking and helps the seasoning layer
Cons
- Does not fit hood-equipped 36 inch models such as 1868 1820 and 1899
- Side panels are not contoured to the slope of the griddle top
- No front panel available
The factory guard is mechanically different from everything else here. Instead of magnets, it uses a hook-and-loop style non-magnetic mount, and the panels are 3.5 inches tall rather than the roughly 1.2 to 1.4 inches typical of the magnetic sets. That taller profile is why it blocks wind so effectively and why it stays where it is.
At 4.6 stars from 644 reviews with 80 percent five-star, it holds the highest rating in the roundup. Reviewers make the contrast themselves, describing it as the guard that does not fall off when the hood closes, which is precisely the failure mode reported for magnetic designs.
The trade-off is compatibility, and it is not a small one. This set does not fit 36 inch griddles that come with a hood, including models 1868, 1820 and 1899. It does work with both front grease and rear grease management, which is broader than most aftermarket sets, and it deflects heat away from the side shelves.
Measure before you order. The back pieces are 17.68 by 3.5 by 0.47 inches and the side pieces 15.75 by 3.5 by 0.43 inches, and the panels are not contoured to the downward slope of the griddle top, so the fit is snug on supported models and absent on others.
Why do non-magnetic panels stay put better in wind
Because there is no magnet to lose. A hook-and-loop mount does not depend on surface contact or on the griddle body staying perfectly flat, and it does not care whether the steel has work-hardened or picked up a coating. On an exposed deck in real gusts that difference shows up quickly.
Is it worth buying an OEM part over an aftermarket set
If your griddle is a supported hoodless model, yes, because fit is guaranteed and the panels are far more rigid. If your 36 inch griddle has a hood, this is the wrong product and one of the magnetic sets above will serve you better.
6. CeOaOtK Magnetic Wind Guards for 22 Inch Blackstone Griddles
Upgraded Wind Guards for Blackstone 22 Inch Griddle, Blackstone Griddle Accessories, Magnetic Stainless Steel Wind Screen for Black stone Grill,Protect Flame Hold Heat Compatible with Hood＆Side Shelf
Stainless steel construction
Upgraded stable magnet structure
Side guards 13.8 in by 1.4 in
0.52 kg
Pros
- Cuts wind-driven heat loss on 22 inch models
- Magnet structure stays put without wobbling
- Works with hood side shelf rear grease cup and cover
- Four panels install in seconds
Cons
- Short 8.7 in back guards leave part of the rear edge open
- Fit depends heavily on which 22 inch model you own
The 22 inch griddle is where wind guards are most useful, because the cooking surface is small enough that a single exposed burner dominates the temperature. This CeOaOtK set concentrates flame back into the cooking zone and reviewers report a visible drop in how often they have to chase the burner setting.
The build is stainless steel with an upgraded magnet structure designed specifically not to shake, which addresses the rattling complaint that comes up with cheaper sets. Side guards measure 13.8 by 1.4 inches, the short back guards 8.7 by 1.4 inches and the set weighs 0.52 kg.
Compatibility covers Blackstone 22 inch models 1666, 1813, 1833, 1842, 1891, 1935, 1940, 2015, 2061 and 2063, and the listing confirms it works with the rear grease cup, side shelf, hood and cover. If you own one of these, the fit is straightforward.
The rear coverage is the part to think about. At 8.7 inches, the back guards are considerably shorter than the 15.7 inch panels used on the 36 inch sets, so a portion of the rear edge stays open to crosswind. On a still day that does not matter; on a gusty patio it is the weak point of the design.
Is a 22 inch griddle windier than a 36 inch griddle
More exposed, in practical terms. A single burner under a small cooking surface has less thermal mass to buffer a gust, so the same wind that merely annoys you on a 36 inch model can shut a 22 inch burner down entirely. That is why guards for this size tend to show the most dramatic improvement.
Will it fit a 22 inch griddle with a hood
Yes, the panels mount low and the listing lists hood compatibility. What matters more is that you own one of the listed models, since the panel lengths are cut for that frame and a mismatch leaves a gap at the rear.
7. Petrirufun Three Sided Wind Guard with Warming Rack for 16 to 28 Inch Griddles
Wind Guard & Griddle Warming Rack for 16″-28″ Hoodless Front Grease Griddle
Adjustable from 16 to 28 inch wide
Retractable and foldable
Three side baffles
17 in by 10 in by 5 in
Pros
- Only option here that is both a three-sided screen and a warming rack
- Adjustable and folds flat for storage
- Reported to stay upright in 50 mph-plus wind
- Works as a backsplash protecting walls and stone
Cons
- Requires screw locking rather than a magnetic or hook-on mount
- Must match front grease rather than rear grease configuration
- Costs more than a magnetic panel set
This is the only product in the roundup that wraps three sides with a rigid frame rather than snapping flat panels to the griddle body. It adjusts to fit hoodless griddles from 16 to 28 inches wide, retracts and folds flat for storage, and includes three side baffles that cut grease splatter. For most buyers the warming rack above the cook surface is the feature that justifies it.
It shares the top rating in this group at 4.6 stars, with 79 percent five-star reviews. Reviewers repeatedly note that it stays upright in very strong wind, which makes sense given the three-sided frame and the screw-locked installation.
It also works beyond Blackstone. The fit list covers Blackstone 17 inch, Cuisinart CGG-501, Camplux 22 and 17 inch, Cecarol 23 inch, Flame King 17 inch, Char-Griller 8217 and Royal Gourmet GB2000, which makes it the broadest non-Blackstone option we found.
The trade-offs are real. Installation needs screws rather than a magnetic snap, and you have to confirm front grease versus rear grease management before it will mount. It also sits above the magnetic panel sets on cost, and at 281 reviews it has the smallest review base here, so treat the durability reports as encouraging rather than proven over many seasons.
Is a screw-locked guard safer in high wind than a magnetic one
It stays attached, which is the important part. A rigid frame with a locked joint will not be lifted or knocked off by a gust in the way a magnet-mounted panel can be, though a taller frame does add load to a griddle that has any lean to it.
Is the warming rack worth the extra cost
If you cook for a group and stage food, yes. It adds usable space above the cook surface at no extra footprint and doubles as a backsplash. If you mostly cook for one or two, the magnetic panel sets do the same wind protection for less.
8. GARNETIN Wind Guard Set for 17 Inch Blackstone Flat Top Griddles
GARNETIN Wind Guard for Blackstone 17 Inch Flat Top Griddle, Set of 4
430 stainless steel with black coating
Magnets rated to 660 F
Side guards 13.8 in by 1.4 in
Set of 4 panels
Pros
- Real measured temperature gain at the edges and corners
- Light enough to leave attached during travel
- Blocks wind and insects at the same time
- Stainless construction has held up over years outdoors
Cons
- Rear guards can be knocked off by the hood on portable models
- Can work loose in a bouncing travel trailer
- Back guards are only 6.3 in and cover less rear edge
Portable 17 inch griddles are the hardest case for a wind guard because the frame is small, the panels are short and a hood on many models sweeps right across the rear edge. This GARNETIN set handles it as well as anything we found for that size, and it works just as well on a camp setup.
The construction is 430 stainless with a black coating and magnets rated to 660 F. Side guards are 13.8 by 1.4 inches and the back guards only 6.3 by 1.4 inches, which is the most compact rear coverage in the roundup and also its main limitation.
The strongest review evidence here is a measured one. One buyer reported the full cook surface reading above 300 F after installation, against 225 to 250 F at the edges beforehand, which is exactly the corner improvement we looked for in our own test. Buyers also credit it for keeping bugs off the food through the same gaps it closes.
Fit covers Blackstone 17 inch models 1650, 1814, 1832, 1933, 1939, 1945, 1971, 1783, 1859 and 1892, and works with the rear grease cup, side shelf, hood and cover. Check your hood clearance carefully, since the short rear panels can be caught by a lid on portable models with rear struts.
Can you leave these attached while transporting a portable griddle
Several owners do exactly that, since the set is light and the magnets hold well on level surfaces. In a bouncing travel trailer the panels can work loose, so we would remove them and pack them separately before a long drive.
Do they work on non-Blackstone portable griddles
They are cut to the 17 inch frame, so on any griddle with a similar footprint and magnetic body they will fit well. Check the guard length against the griddle top width before ordering, since the fit is dimensional rather than universal.
9. BSTTEK Vented Wind Guards for 22 Inch Griddles
Wind Guards for Blackstone,22 inch Magnetic Blackstone Griddle Accessories
430 stainless with anti-corrosion coating
Ventilation holes in each panel
Installs in about 30 seconds
13.8 in by 1.4 in by 0.9 in
Pros
- Vented panels avoid the overheating solid guards cause
- Keeps side shelves cooler for bottles and tools
- Dishwasher safe and wipes clean
- Quickest tool-free install in the roundup
Cons
- Adhesive holding the magnets can fail with heat
- Not for the Blackstone On the Go series
- Panels can pop off when the griddle is moved
Every solid panel in this roundup raises the same complaint: with the wind blocked, there is nowhere for expanding air to go, and the surface can overshoot. The BSTTEK set is the answer to that. Each panel has ventilation holes punched through it, so oxygen flow to the burners stays steady while the heat stays contained.
That single design choice shows up repeatedly in the reviews. Buyers report no heat build-up problems at all, and several specifically note that the side shelves stay cool enough for condiment bottles. The panels are 430 stainless with an anti-corrosion coating and the whole set is dishwasher safe.
Installation is a genuine outlier for the better. Tool-free magnetic attachment, rounded edges and a stated 30 seconds to fit or remove. Side guards measure 13.8 by 1.4 inches with the set at 0.9 inches thick, so the profile is slim and low enough to clear most hood travel.
The weak point is the magnet adhesive. Reviewers report panels dropping when the griddle is bumped or moved for storage, which suggests a bond that is weaker than the welded or glued options. Fit covers Blackstone 22 inch models 1666, 1813, 1833, 1842, 1891, 1940, 2015, 2061 and 2063, but not the On the Go series.
Do vent holes reduce wind protection
Somewhat, and that is the honest trade. The holes are small and numerous enough that burner stability remains good in breezy conditions, but this set will not hold back a hard gust the way a solid panel does. If your patio gets occasional strong wind rather than constant moderate wind, the venting is worth the trade. If it gets real gusts, a solid panel is the safer choice.
Can you wash these in a dishwasher
The listing states the set is dishwasher safe, which removes the usual maintenance objection to stainless panels. Wipe them after cooking and put them through a cycle occasionally, and the coating stays in good shape.
10. Koutemie Matte Black Magnetic Wind Screen for 36 Inch Griddles
Koutemie Magnetic Wind Screen of Blackstone Wind Guards 36 Inch, 4 Pcs
Powder-coated high-temperature metal
16.9 in by 1.4 in panel profile
Model KTM-WGB-36 for 36 inch
0.55 kg
Pros
- Strong magnets that secure panels firmly
- Panels can be oriented for airflow from above or below
- Matte black finish looks integrated rather than added on
- Available in 17 22 28 and 36 inch sizes
Cons
- Small magnets can fall from their slots and block burner ignition
- Panels can be bumped off while scraping the surface
- Side guards sit slightly short on some models giving partial coverage
The Koutemie screen finishes in matte black, and for anyone whose griddle is black that matters more than it sounds. A bright stainless panel set on a black frame reads as an accessory. This one reads as part of the cooker, which is the same trick the MeWeBlue set plays with its black coating.
Construction is heavy-duty powder-coated high-temperature metal on a 16.9 by 1.4 by 0.9 inch panel profile, model KTM-WGB-36, at 0.55 kg. Reviewers like the magnet strength and, unusually, the ability to mount the pieces to draw air in from the top or from below depending on conditions.
At 4.5 stars from 304 reviews with a 77 percent five-star share, the satisfaction rate is high. Owners report a noticeably hotter flat top, shorter cook times and improved combustion efficiency, which translates into less propane burned for the same result.
There are two practical warnings. The small magnets can drop out of their slots and must be removed before lighting a burner, and the side guards can sit slightly short on some models, giving partial rather than continuous coverage. Variants exist for 17, 22 and 28 inch griddles, though those smaller versions may need slight adjustment to fit.
Can the panels be mounted in different orientations
Yes, and it is a genuine advantage in variable wind. Angling the panels to pull air across the firebox from above, or up from below, lets you change how the guard behaves when a gust approaches from a different direction without taking anything apart.
Are the small magnets a safety problem
They are an inconvenience rather than a hazard, provided you check the slots before lighting. A magnet sitting in a burner area is exactly why we would give the griddle a quick visual before every light in a season where the panels take a lot of knocks.
What Size Wind Guard Do You Need?
Match the guard to the width of the griddle top, not the width of the frame, and confirm three things before you order: whether your griddle has a hood, whether the grease cup drains from the front or the rear, and the model number. Those three answers eliminate nearly every fit complaint we read.
For 17 inch tabletop griddles, the guard is usually a short side panel plus a small rear panel, and the model number matters most because hood clearance is tight. For 22 inch griddles you will find the widest range of options, including the only vented design in this roundup. For 28 inch griddles, check that the listing covers your specific frame rather than assuming it scales from 22.
For 30 to 32 inch griddles, the guard is usually sold as a 36 inch set with the outer panels overlapping the ends. It works, but the fit is less tidy. For 36 inch griddles you have the most choice, and the deciding question becomes the hood.
Hood-equipped 36 inch models are the biggest trap in this category. Several of the guards here explicitly exclude them, and the factory 5015 set is not for hooded units at all. Front grease versus rear grease management is the second trap: panels that sit over the wrong drainage path can block grease from leaving the firebox, and reviews mention that interference specifically.
If you own a 17 inch rear-grease-trap model, the honest answer is that aftermarket fit is limited, and the Petrirufun adjustable frame is the safer bet because it spans widths rather than matching one model.
Do You Actually Need a Griddle Wind Screen?
The skeptic argument is the most common one in griddle forums, and it is not wrong at its core. The claim is that the food itself cools the surface, so a guard adds nothing. That is true on a still day, and it is the reason a guard can seem like a placebo if you test it in calm weather.
The argument fails because wind is the third heat sink, alongside food and ambient air, and it is the only one you can turn off. The Barbecue Lab’s forced-air test showed standard flat-top designs losing an average of 71 to 199 degrees once air was pushed across the surface. Recessed-cooktop designs, which sit lower in the frame and are inherently sheltered, lost roughly a quarter of that. A perimeter screen is a cheap way to borrow the same shelter.
There is a second reason that shows up in review data more than in theory. Wind tilts a flame rather than extinguishing it, and a leaning flame does not heat the surface evenly. That is the mechanism behind the cold bands people report at the front and rear edges, and it is why a guard can leave the centre temperature unchanged while the corners come up noticeably.
You need one if any of the following are true. If your burners go out when you try to hold low heat, a guard is the cheapest fix available. If the back third of your griddle is always cooler than the front, crosswind is the likely cause. If you cook low and slow outdoors through the shoulder season, a guard will reduce propane use noticeably.
You probably do not need one if your patio is sheltered by a wall on the windward side, if you cook at high heat where heat loss is a rounding error, or if you already use a hard hood and keep it down. Adding a screen to a properly sheltered setup mostly adds overheating problems.
Magnetic or Fixed Mount: Which One Survives a Gust?
Panel height is the first variable. The magnetic sets in this roundup run roughly 1.2 to 1.4 inches tall, which is enough to redirect flame but not enough to change airflow dramatically. The factory set is 3.5 inches tall, and users describe it as noticeably more substantial in wind for that reason alone.
Mount style is the second. Magnets are fast, tool-free and removable in seconds, which is why eight of the ten products here use them. The weakness is that magnet strength depends on flat steel and even contact, and a panel that is bumped while scraping or lifted by a hard gust has to be reseated. Non-magnetic mounts stay attached but require more deliberate installation.
Materials decide longevity. 304 stainless resists corrosion best and suits coastal air. 430 stainless is a close second and is what most of these sets use. Powder-coated carbon steel looks the best on a black griddle but needs to be dried before winter storage or it will bloom.
Two safety points deserve attention. Tall panels add side load to a griddle frame that already leans, so if yours is not perfectly level, address that before adding height. And check that no panel sits across a grease drainage path, because blocked drainage causes flare-ups that no wind guard is worth.
Wind Guard vs Hood vs Recessed Cooktop
A hood is the most complete answer to wind and the most expensive, because it changes how the whole cooker operates. It also adds weight high on the frame, which matters on a griddle with a tipping history. Most guards here are explicitly designed to work with a hood, so the two are complementary rather than competing.
A recessed cooktop is the design answer. Sitting the cooking surface down inside the frame puts the burners in a natural wind shadow, which is exactly why the recessed models in The Barbecue Lab’s test lost only about 71 to 75 degrees under forced air compared with 134 to 199 for conventional designs. It is the only approach that solves the problem without any add-on.
A wind screen is the cheap retrofit. It costs a fraction of a hood, fits in seconds, and addresses the flame-tilting and edge-chilling parts of the problem directly. It does not seal the surface the way a hood does, so you will always manage more airflow than with a closed design.
Our practical advice is to buy the screen first and live with the results for a season. If that resolves your cold edges and relighting, a hood or a recessed-cooktop griddle is a later upgrade rather than a first purchase. The gas grills we recommend for windy conditions cover the hooded end of the same problem if you decide you want full enclosure.
Patio Wind Layering: Awnings, Screens and Griddle Guards
A griddle guard solves wind at the firebox. It does not solve cold ambient temperature, sun on the cooking surface, or wind chill while you stand there. On a genuinely exposed patio, layering works better than any single product.
The most effective layer is a solid windbreak above head height and behind the cooking position, because it takes the pressure off the flame without trapping burner air. Privacy screens and outdoor blinds do this well, and they also cut radiant heat in summer, which helps on the same afternoons that produce the gusts.
An awning or pergola cover is the second layer. It reduces ambient temperature and sun load on the griddle top, which means less propane for the same surface temperature. That is a different saving from the wind guard’s, and the two compound.
The third layer is the guard itself, placed as the innermost barrier. Keep wind direction in mind when you arrange them, since a screen that blocks one direction can funnel wind into a narrow gap and make the local exposure worse rather than better.
If you are building out a wind-exposed space and want the structure itself to perform, our guide to greenhouses for windy areas covers frame and glazing choices that handle high wind loads. A simple wind chime is a surprisingly decent way to gauge how gusty a spot is before you spend anything on it.
How to Make a DIY Griddle Wind Guard (and When It Is Worth It)
A home build makes sense in one situation: a non-standard griddle size that no listed product covers. Otherwise, a stamped steel panel set is cheaper, flatter and has a better magnet fit than anything you can assemble.
If you do build, this is the order that works. Measure the griddle top width and the depth from the front edge to the rear grease path, then cut three panels to those dimensions, leaving a quarter inch of clearance at each corner. Choose a steel gauge thick enough to resist warping, and keep panel height under 3 inches so heat does not build. Attach high-temperature magnets with adhesive or mechanical fasteners, positioning them on the underside so they clear the scrape zone. Dry-fit all three panels before any burner is lit, and confirm nothing blocks the grease drain or the hood hinge. Finally, check the finished panels on the bare griddle body to confirm contact across the whole edge.
Build only when no commercial guard fits your measurements. If a listed product covers your model, it will have better steel, better magnets and a warranty, and it will still be there next season.
Frequently Asked Questions
How to make wind guards for blackstone griddle?
Measure the griddle top width and the depth from the front edge to the rear grease path, then cut three panels to size with a quarter inch of clearance at each corner. Keep panel height under 3 inches so heat does not build underneath. Attach high-temperature magnets on the underside of each panel so they stay clear of the scrape zone. Dry-fit all three panels with the burners off, confirm nothing blocks the rear grease drain or the hood hinge, then test on the bare griddle body to check contact across the whole edge. Building only makes sense when no commercial guard matches your griddle size.
Does Blackstone make wind guards for griddles?
Yes, the factory 5015 set is a genuine original part with four powder-coated metal panels mounted by a hook-and-loop style non-magnetic fitting. It works with both front grease and rear grease management 36 inch griddles. It does not fit 36 inch units that come with a hood, including models 1868, 1820 and 1899, so check your model number before ordering.
Do wind guards help a griddle hold heat?
They do, and the improvement is largest at the edges and corners. Wind tilts the flame instead of just cooling the surface, which is what creates cold bands at the front and rear of a griddle. In forced-air testing of 7.5 to 8 mph, standard flat-top designs shed an average of 71 to 199 degrees of surface temperature, so blocking that airflow is a measurable gain rather than a placebo.
Will a wind guard fit my griddle hood?
Most magnetic sets are designed to work with a hood because they mount low on the griddle body and leave the hinge and warming rack area clear. The exceptions matter though: the factory 5015 set does not fit hood-equipped 36 inch models at all, and longer back panels on some 304 stainless sets can sit close to the lid travel. Match the model number against the listing rather than relying on griddle width alone.
Are magnetic wind guards strong enough in high wind?
For a griddle that stays in place during cooking, yes. The panels sit on the bottom edge of the griddle top and hold through a full session in normal conditions. In heavy gusts a magnetic panel can lift or be knocked off, which is the argument for a screw-locked frame guard or a non-magnetic factory set. Avoid leaving panels attached before moving a portable griddle for storage, since magnet adhesive can fail when the unit is bumped.
Final Verdict: The Best Griddle Wind Screen for Your Patio
For most people reading this on an exposed patio, the MeWeBlue set for 36 inch griddles is the best griddle wind screen to buy. It has the deepest review base in the category at more than 3,500 ratings, the compatibility list covers most 36 inch models including hooded ones, and the recurring reports describe exactly the improvement we measured on our own deck. Expect to relearn your burner setting, because trapped heat genuinely changes how the griddle behaves at low settings.
If your 36 inch griddle has no hood, the factory 5015 set is the better mechanical answer, with taller 3.5 inch panels and a non-magnetic mount that stays where magnets slip. For 22 inch griddles the CeOaOtK set is solid on wind blocking, and the BSTTEK vented set is the answer if overheating is your problem. Tabletop owners should look at GARNETIN for 17 inch models, and the Petrirufun frame is the pick when you want a warming rack and a backsplash in the same piece.
Check three numbers before you order: your griddle width, whether it has a hood, and whether the grease cup drains from the front or the rear. Get those right and any of the picks above will do the job. Get them wrong and none of them will.
We tested these on an exposed deck and updated the guide for 2026. If you want to see how much wind your spot actually gets before you decide, start with a simple anemometer reading, then fit a guard and compare.